Hydraullic driven rotating head 8700Nm

Article: TIEH-8700
Rating:
(0 votes)

Hydraulic driven rotating head is a hydraulic driven device which is connected with the top of the helical screw piles by means of appropriate adapter and with use of hydraulic power send its torque force onto the top of the screw pile to rotate (ground) helical screw pile into the soil.

Our hydraulic driven rotating head can not work alone. It must be plugged to the source of hydrauic power. To see the complete set of our 'screw piles installation equipment set' please see appropriate page here >> There are 6 set models presented within these pages where only one main hydraulic station is used along with 6 different models of hydraulic rotating heads.  

Complete installation set is designated to screw into the soil various types of helical metal screw piles which form piles foundation for houses and various types of constructions. The main advantage of this equipment is compact size and affordable weight for human handling and therefore high ability to be transported (wheeled) to sites with limited space and virgin lands. Powered by 'Honda' single cylinder, 4 stroke engine which is fed by gazoline. Economic consumtion of gazoline. Present equipment does not require any electricity. 

COMPONENTS OF HYDRAULIC ROTATING HEAD:

1.Hydraulic drive head -1pc
2.Holder (for leverage fixing) -2pc.
3. High pressure hoses with quick couplers (L=0.5m) -2pcs.
4.Spline shaft with flange -1pc.
5. Torque pin (splint) -1pc.

Hydraulic driven rotating head is applicable to work with steel screw piles with diameter from 57 up to 159 mm with pile's thickness 3.0-5.0 mm. Our rotating head is having noticeable torque and therefore we recommend to use only metallic helical screw piles with thickness of the helical pile body not less then 3,0 mm. Otherwise the hydraulic torque can tear off the metal body of the pile.

Various types of metallic helical screw piles our head can work with:

types of helical screw piles  

Our hydraulic driven rotating head must be connected with the top of the screw pile by means of metal connector and metal pin. Two persons normally undertake screw pile's positioning (with drive head on the top of it), while operator serves hydraulic power unit. Once torgue is on, one of two positioning operators must take leverage into his hands to compensate torque force on the screw pile's end because of screwing movement. Having torque 'on' and fixed leverage compensation the screw pile has nothing to do but to dig into the soil until obstruction is met by the pile. Obstraction can be stones or likely, or heavy soil such as Cambrian clay. One screw pile with 2.0 m length normally take 8-10 minutes to be screwed into the soil almost completely, if no serious obstructions are met. 

Our company 'Agency 'New Technologies', INN (tax reg no) 7807319158 is an official representative of the Russian manufacturing factory producing hydraulic equipment under the trade mark 'Torsion'.  Our prices are absolutely the same with manufacturer's prices and our Principal's web page is having back hyperlink to our web page as a purchasing tool to buy on-line. Our web page rusexportstore.ru prime target is to simplify to our foreign buyers the whole process of purchasing of russian commodities and instruments in terms of logistics and custom's clearance operations on both shipper's and consignee's ends.

Should You have any comments or any questions please feel it easy to proceed with Your question by clicking 'Reviews' button on the product menu line. We will revert with our comprehensive answer as soon as possible.

Leave feedback
Fill required fields (marked by) *.
1 2 3 4 5

Hydraullic driven rotating head specification
(head to be put onto the top of the screw pile) 

Rated torque 8700 Nm
Inlet pressure (nominal) 16 MPa
Inlet pressure (max) 20 MPa
Weight (without holding bracket) 32-80 kg
The temperature range of the oil fpom +15°С to +70°С
Interval of ambient temperatures from -40°С to +40°С
Speed (nominal) 3-15 rpm

Hydraulic driven rotating head connected with its power supplying station is a high-torque force with low rotating speed which allows operators to act quite safely and at the same time quite efficient in any circumstances and in any limited spaced to ground (screw) helical piles into the soil. Due to the fact that our screw piles piles installation equipment is very compact and mobile it can give additional advantage to operate on different landscapes which have noticeable slopes which make operation of huge machines impossible. Our equipment can work on extreme slopes.

High Pressure hoses specification.
The basic configuration of equipment includes 2 high-pressure hoses with a length of 5 m each. They are designed to connect the hydraulic power unit with the working mechanism (hydraulic drive head in our case, any other hydraulic equipment suitable for pluggin with main hydraulic engine unit). By means of the high-pressure hoses the working fluid (oil) flows from the hydraulic power unit to the hydraulic drive head. During the operation, especially on difficult soils, high-pressure hoses are subjected to a high load associated with the increase in pressure of the working fluid flowing inside them; therefore in our products we use high-pressure hoses only of a reliable manufacturer with a 2-fold safety factor. High-pressure hoses are equipped with quick couplings.

Below photographs expose the work of hydraulic driven rotating head. This tool is always on top of the screw pile. You can see leverage fixing rotating head to compensate it's torque against the pile. Our hydraulic rotating head can not work alone. It needs hydraulic power to be connected with. Below pictures show what You can do with our 'screw piles installation set' which uses our rotating head as a main rotating tool.

'Torsion' screw piles installation equipment set is a portable one.
which can be wheeled by only one operator to virgin lands or to the sites with limited space. Wheeled hydraulic unit weights approx 80 kgs. This equipment is made in Russia by geniune russian engineers. 

screw piles instanllation equipment set gazoline russian origin screwpilesinsthelical screw piles installation equipment set 04 helical screw piles installation equipment set 02
helical screw piles installation equipment set 03 helical screw piles installation equipment set 01 helical screw piles installation equipment set 03 (2)

Screw piles can be grounded into the soil with use of this equipment and with 1 operatior and normally 2 workmen involved. With kriner piles with length not exeeding 1,5 meters 1 operator and 1 workman are enough to execute pile screwing into the soil. Once pile is not krinner but screw pile with wide blade or any kind of screw piles with length exceeding 1,5 or 2,0 meters long (high), then 1 operator +2 workmen will be required. Since one operator is constantly serving the hydraulic machine two workmen (1) pop up the pile, (2) keeping the rotating pile in vertical position (3) handling one leverage to compensate torque force on the pile's end. Once two leverages are used then 1 additional workmen will be required. Two leverages are required with heavy soils. Our equipment is strong enough to get 4 workmen on two leverages to slip over at a high torque force on the pile's end (other words when strong clay is met by the grounded pile, then even four wormen, per two on each leverages can hardly resist such a pressure. All four workmen can be sweeped away. Metallic tubes used as a leverages can get deformation. This shows potential torque of our equipment).

 

Screw piles foundation 6x6m completed with use of Torsion screw piles installation set.
Photographs below show screw piles foundation for a wooden house 6x6 meters. Foundation consists approximately of 18 screw piles of 108 mm diameter each. All piles were 3,0 m long (a bit more then normal) and while being grounded deeply into the soil had partially passed through a heavy clay. Anyhow all piles were completely grounded to a certain level. Once all piles were grounded tops of which were marked by a level and went cut off. We put dry mix into the inner hollow of all piles to exclude air (oxidation) of piles from inside. Pile's top were all capped by 200x200mm cap which was then welded to the pile itself to fix it's stable position. Caps are normally used as a landing surfaces for a grillage (wooden beams 200x200mm).

screw piles foundation for 6x6 meter house 04 screw piles foundation for 6x6 meter house 02 screw piles foundation for 6x6 meter house 01
grillage by 200x200mm wooden beam upon screw piles foundation for 6x6m house 02 grillage by 200x200mm wooden beam upon screw piles foundation for 6x6m house 01 grillage by 200x200mm wooden beam upon screw piles foundation for 6x6m house 03
grillage upon screw piles foundation for 6x6 meter house 05 grillage by 200x200mm wooden beam upon screw piles foundation for 6x6m house 15 grillage by 200x200mm wooden beam upon screw piles foundation for 6x6m house 14
Works were executed in the vicinity of St.Petersburg, Russia. 

 

Screw piles 60m long foundation for fence completed with use of Torsion screw piles installation set.
Below photographs shows grounding of 25 x 57 mm screw piles for future fence. The nature of soil was partially presented by strong clay which cause higher torque forces (then normally met) which finally broke up our pile connector. See below. Anyhow 60 meter long foundation was set up in approximately 3 hours. In case to enforce screw pile connectors we use outer in inner connectors. Outer type is a bit more stronger and durable. 

screw piles installation equipment in use screwing 57mm piles for fence 02 screw piles installation equipment in use screwing 57mm piles for fence 04 screw piles installation equipment in use screwing 57mm piles for fence 03 screw piles installation equipment in use screwing 57mm piles for fence 06
trouble with screw pile connector 01 trouble with screw pile connector 02 trouble with screw pile connector 03 screw piles installation equipment in use screwing 57mm piles for fence 02
Works were executed in the vicinity of St.Petersburg, Russia. 

 

Winter operations of screw piles grounding with use of Torsion screw piles installation set.
Below photographs shows grounding of 6 x 89 mm screw piles as foundation for standard 20'ft dv sea container. Works were executed in April (still winter time in Russia). Outdoor temperature was at a level of minus 10 degrees Celcius. Our equipment had shown perfect stable work during winter time operations. At least hydraulic oil which is presented in the system must be avove '0' to start operations. During operations oil is getting warmer itself and screwing process goes smooth as usual. To start the engine in 'minus' outdoor temperatures requires oil temperature level be not lower then zero deg C. In our region, in Russia, were we live, we ground screw piles at a minimum level of 1,4 meter deep into the soil. This deep soil lever is not affected by winter freeze and therefore will not cause soil swelling which in its turn can pop up screw pile. Even small pile's fluctuation off its original grounding may cause severe damage to the building.

screw pile installation equipment in operation in April with minus 10C iii screw pile installation equipment in operation in April with minus 10C iv screw pile installation equipment in operation in April with minus 10deg C  screw pile installation equipment in operation in April with minus 10 deg C screw pile installation equipment in operation in April with minus 10 deg Celcius screw pile installation equipment in operation in April with minus 10 deg C ii
Works were executed in the vicinity of St.Petersburg, Russia. 

 

Screw piles foundation performed by Torsion installation set is easy to perform and definately cost effective.
Below photographs show leveling of screw piles and grillage and fastening pile's cap to the wooden beam grillage. Installation of screw piles foundation can be executed easily by Torsion hydraulic driven screw piles installation set. 

grillage foundation level precise positioning 01 grillage foundation level precise positioning 02 grillage upon screw piles foundation for 6x6 meter house 03
grillage by 200x200mm wooden beam upon screw piles foundation for 6x6m house 15 fixing screw pile top cover with wooden beam grillage 03 fixing screw pile top cover with wooden beam grillage 01
Works were executed in the vicinity of St.Petersburg, Russia. 

 

Krinner screw piles type employed by Torsion screw piles installation set.
Krinner types of screw piles with short length (top) can be worked out by a gang of two workmen (as shown on the photo). And if soil allows. In case of heavy soil at least 1 operator + 2 workmen will be required to position pile and keep control on leverage to compensate torque on the pile's end.

russian origin hydraulic screw piles installation equipment set
Works were executed in Germany. 

 

Our company 'Agency 'New Technologies' is an official representative of the Russian manufacturing factory producing hydraulic equipment under the trade mark 'Torsion'. 

Should You have any comments or any questions please feel it easy to proceed with Your question by clicking 'Reviews' button on the product menu line.

'Torsion' screw piles installation equipment set in operation. 
Grounding Krinner type screw piles into the soil. Operations undertaken in Germany.

   

 

 

Our company 'Agency 'New Technologies' is an official representative of the Russian manufacturing factory producing hydraulic equipment under the trade mark 'Torsion'. 

Should You have any comments or any questions please feel it easy to proceed with Your question by clicking 'Reviews' button on the product menu line.

The price shown in the main icon is the price FCA V.Novgorod, Russia.
V.A.T. = 0%. (Price include 'zero' value added tax).
Price apply to foreign purchasers, outside territory of Russian Federation.

This price FCA V.Novgorod, Russia does not include the following additional expenses: 
(i) customs clearance costs in Russia
(ii) transport costs to the buyer
(iii) customs clearance in the buyer's country

On this page we would like to give You and example of estimation of additional costs:
Most of rates shown below are estimations, which are very much close to true rates.

 

Should we ship hydraulic rotating head by TRUCK, for example to HAMBURG:
+200 EURO = Custom's clearance in Russia = 200 EURO per custom's declaration  
+230 EURO = Transporting costs from V.Novgorod to Hamburg = 230 EURO per 1 wooden crate 900x500 mm, approx 60 kgs. 
+50 EURO = Custom's clearance in Germany = 50 EURO per custom's declaration
+XX EURO = Custom's duties and fees in Germany = ask Your local custom's broker for calculation

 

Should we ship hydraulic rotating head by SEA CONTAINER, for example to KOLKATA, INDIA:
+200 EURO = Custom's clearance in Russia = 200 EURO per custom's declaration  
+60 EURO = Port expedition services in the port of St.Petersburg, Russia = 60 EURO per Bill of Ladding
+120 EURO = Ocean freight costs St.Petersburg, Russia -Kolkata, India = 120 EURO per 1 wooden crate 900x500 mm, approx 60 kgs. 
+40 EURO = Port expedition in the port of Kolkata, India = 40 EURO per Bill of Ladding
+50 EURO = Custom's clearance in Kolkata, India = 50 EURO per custom's declaration
+XX EURO = Custom's duties and fees in India = ask Your local custom's broker for calculation
+XX EURO = possible small size costs for terminal handling opertions inside the port = ask Your local port expeditor for calculation

 

Useful TIP: Regarding Customs clearance: Once You buy 1 article then costs for customs clearance will be as much as 200 EURO per customs declaration (as shown above). Should You intend to buy some additional articles, for example screw piles, then +15 EURO per additional article. This additional article will be inserted into the same customs declaration. Each article inserted into the customs declaration will have their own identification customs code: 'hs code' (harmonized system code). Other words the very first hs code will imply 200 EURO per customs declaration. Any other additional hs code to be inserted into the same customs declaration will imply +15 EURO per additional hs code. It means the more articles You buy the less average fee is payed per article per customs clearance.

Useful TIP: For those clients and purchasers who would like to receive complete "door-to-door" service we can arrange complete service on the consignee's end, i.e. port expedition in the port of destination, customs clearance at destination, on-carriage on customer's terrain, delivering to the customers warehouse or site and dropp-off of empties (container equipment). These are DDP terms.

Useful TIP: Buyer can book cargo survey prior cargo's dispatch to it's consignee. Cargo survey can be executed by the St.Petersburg Chamber of Commerce and Industry. Cargo survey is done in respect of evaluation of quality and quantity. Costs for cargo survey relay on the buyer. Our company is a registered member of the St.Petersburg CCI and therefore we apply to reduced costs as an active member and therefore can help to reduce cargo survey costs to our potential buyer.

Our company 'Agency 'New Technologies' is an official representative of the Russian manufacturing factory producing hydraulic equipment under the trade mark 'Torsion'. 

Should You have any comments or any questions please feel it easy to proceed with Your question by clicking 'Reviews' button on the product menu line.

'Torsion' hydraulic driven rotating head can be purchased on a basis of full 100% prepayment. Typical Purchase Agreement can be forwarded upon request. Production time normally takes 5-10 working days (1-2 calendar weeks). Payment can be done in Russian roubles, US Dollars or Euro by banking transfer. Our correspoinding bank: JSC Raiffeisen Bank, Russia. We can also work on a basis of L/C for USD and EURO payments where all costs on L/C opening are on the purchaser's expense. 

Buyer can book cargo survey prior cargo's dispatch to it's consignee. Cargo survey can be executed by the St.Petersburg Chamber of Commerce and Industry. Cargo survey is done in respect of evaluation of quality and quantity. Costs for cargo survey relay on the buyer. Our company is a registered member of the St.Petersburg CCI and therefore we apply to reduced costs as an active member and therefore can help to reduce cargo survey costs to our potential buyer.

Our company 'Agency 'New Technologies' is an official representative of the Russian manufacturing factory producing hydraulic equipment under the trade mark 'Torsion'. 

Should You have any comments or any questions please feel it easy to proceed with Your question by clicking 'Reviews' button on the product menu line.

'Torsion' hydraulic rotating head fits less then a single pallet dispatch.

Our rotating head can be packed into 1 wooden crate 900x500 mm, approx 60 kgs. It can be shipped as a parcell or as a LTL/LCL (less truck or container load). Below is an example of what we do when a complete set of equipment is dispatched.

Normally 1 complete set of our 'Screw piles installation equipment' is purchased at a time. This consist of hydraulic power unit with dimensions (LхWхH) 870х840х755 mm, which is the biggest tool, and hydraulic drive head which is comparatively small, but is having 37,5 kg of weight itself+ 20 kgs of head's accessories. The rest of the cargo is high pressure hoses (5 or 10 meters) and adaptor(s) which does not ask for much space at all. In the end all these set can be put on the top of one normal europallet (80 mm x 120 mm), the weight of all things on this pallet can be as much as 140-160 kgs. You can see pictures below:

Hydraulic powered screw piles inst equip packing view 03 Hydraulic powered screw piles inst equip packing view 02  Hydraulic powered screw piles inst equip packing view 01

Normally cargo placed on 1 pallet (which is ready to be dispatch to a client) is called as LTL (less truck load) of LCL (less container load). Opposite situation is with the complete staffing of goods into one space: i.e. with FTL (full truck load) or FCL (full container load). In our case we will ship this 1 euro pallet as LTL or LCL which will certainly cost much less transporting charge as those cargoes which are being shipped in "full load". For those customers where we can arrange terrain delivery, i.e. by truck we will dispatch this cargo as LTL (by truck, and trucking company will charge only fo 1 europallet). Delivering by truck is possible for those consignees which are located in European countries, CIS, and some Mid East countries. To dispatch this cargo to consignees apart from those described above we will use LCL (by container). Port of load will be St.Petersburg. Port of delivery will be our consignee's home port. It is up to our client to deside terms of delivery: in both cases it will be LTL or LCL. We can provide terms CIP, DAT, DAP, DDU. These terms means that custom's clearance in Russia we will conduct ouselves (on the buyer's expence), but custom's clearance at the consignee's end is optional and to be agreed between the parties. If consignee wishes we can arrange "door-to-door" full service.

For those clients and purchasers who would like to receive complete "door-to-door" service we can arrange complete service on the consignee's end, i.e. port expedition in the port of destination, customs clearance at destination, on-carriage on customer's terrain, delivering to the customers warehouse or site and dropp-off of empties (container equipment). These are DDP terms.

Indication of transit time for LTL cargo within EC countries and CIS: 3-5 max 7 days and depending on the traffic jams at borders (frontiers). Indication of transit time for LCL depends on the country of destination and can be as long as 30-45 days for those countries which port is really far away from St.Petersburg port (our home port). 

Buyer can book cargo survey prior cargo's dispatch to it's consignee. Cargo survey can be executed by the St.Petersburg Chamber of Commerce and Industry. Cargo survey is done in respect of evaluation of quality and quantity. Costs for cargo survey relay on the buyer. Our company is a registered member of the St.Petersburg CCI and therefore we apply to reduced costs as an active member and therefore can help to reduce cargo survey costs to our potential buyer.

Our company 'Agency 'New Technologies' is an official representative of the Russian manufacturing factory producing hydraulic equipment under the trade mark 'Torsion'. 

Should You have any comments or any questions please feel it easy to proceed with Your question by clicking 'Reviews' button on the product menu line.

Is located in sections

Back

Russian export: we ship it easy

"ANT EXPORT" BEARS VALUE FOR THE FOREIGN PURCHASERS 

join
18.12.2025 12:56